Boost Tracer Instruction Manual

Tracer-4210RN / 4215RN —— Maximum Power Point Tracking Solar Charge Controller Thank you very much for selecting our product! This manual

6 Step 4: Drill Holes Remove the controller and drill four sizeable holes in the marked locations. Step 5: Secure Controller Place the controller on

7 Before connecting the battery, measure the battery voltage. It must be over 9V to power the controller. For 24V, the voltage must be greater than 18

8 The Tracer can accept 12V, 24V nominal off-grid solar module arrays. Grid –tie solar module(s) may be used if the open circuit voltage does not exce

9 4 Operation 4.1 MPPT Technology The Tracer utilizes Maximum Power Point Tracking technology to extract maximum power from the solar module

10 Current VS. Voltage in 12V system Output power in 12V system Figure 4-1 Nominal 12V Solar Module I-V curve and output power gra

11 Figure 4-2 Tracer MPPT charging algorithm ·Bulk Charge In this stage, the battery voltage has not yet reached boost voltage and 100% of avail

12 ·Equalize WARNING: Risk of explosion! Equalizing flooded battery can produce explosive gases, so well ventilation of bat

13  Charging Indicator The green LED indicator will light whenever sunlight is available for battery charging, the green charging LED will

14  Load indicator When the load amp is 1.25times of rated current for 60 seconds, or the load amp is 1.5 times of rated current for 5 seconds (overl

15 4.4 Setting Operation  Dual Timer Function The default night length is 10 hours.The contro

16  Load Work Mode Setting Timer1 Setting indicator Work mode LED digital tube Figure 4-4 Instr

17 Load work mode Table 4-5 Timer1 LED Digital No. Disable n

18 Load work mode Table 4-6 Timer2 LED Digital No. Disable n Load wil

19 5 Protections, Troubleshooting and Maintenance 5.1 Protection ·PV Array Short Circuit If PV array short circuit occurs, clear it to resume normal o

20 5.2 Troubleshooting Trouble Shooting Table 5-1 Faults Possible reasons Troubleshooting Charging L

21 5.3 Maintenance The following inspections and maintenance tasks are recommended at least two times per year for best controller performance.  Chec

22 6 Warranty The Tracer charge controller is warranted to be free from defects for a period of TWO (2) years from the date of shipment t

23 7 Technical Specifications • Electrical Parameters Description Parameter Nominal System Voltage 12VDC / 24VDC Auto work Rated Charge Current 40A Ra

24 • Threshold Voltage Description Parameter NTTV (Night Time Threshold Voltage) 5V; x2/24V DTTV (Day Time Threshold Voltage) 6V; x2/24V • Temp compe

PV Power — Conversion Efficiency Curve Illumination Intensity: 1000W/m2 Temperature: 25℃ Tracer-4210RN: 1. Solar Module MPP Voltage(17V) / N

Tracer-4210RN / 4215RN —— Maximum Power Point Tracking Solar Charge Controller System Voltage 12 / 24VDC Rated Charge

3. Solar Module MPP Voltage(68V) / Nominal System Voltage(12V) 4. Solar Module MPP Voltage(34V) / Nominal System Voltage(24V) 88.5%89.5%90.5%

5. Solar Module MPP Voltage(68V) / Nominal System Voltage(24V) 75.0%80.0%85.0%90.0%95.0%100.0%309015021027033039045051057063069075081

Tracer Dimensions (mm)

BEIJING EPSOLAR TECHNOLOGY CO., LTD. Tel：010-82894112 / 82894962 Fax：010-82894882 E-mail：[email protected] Website：www.e

Contents 1 Important Safety Information ... 1 2 General Information ...

1 1 Important Safety Information Save These Instructions This manual contains important safety, installation and operating instructions for

2 2 General Information 2.1 Overview Thank you for selecting the Tracer controller which represents advanced technology of our company. The features a

3 The features of Tracer controller:

4 1 – Charging Status LED Indicator An LED indicator that shows charging status and overvoltage of battery. 2 – Battery Status LED Indicator An LED

5 3 Installation Instructions 3.1 General Installation Notes Read through the entire installation section first before beginning installation. Be ve